TechTalk (Moderator: admin)

Compression

Started by rockinjer

Replies: 2
Views: 1,374

March 21, 2011, 11:39:09 PM
by rockinjer

Clean those electric connectors

Started by EH

Replies: 1
Views: 1,377

April 01, 2009, 02:02:20 PM
by vadasz1

is there a compatible parts list?

Started by Kiwi

Replies: 2
Views: 1,377

July 08, 2009, 06:48:16 PM
by Night Vision

Front end

Started by Kid Jedi

Replies: 1
Views: 1,378

May 15, 2009, 03:40:35 AM
by Rick G

Coolant

Started by Jimustanguitar

Replies: 3
Views: 1,380

June 08, 2009, 06:27:23 PM
by QBS

AFR readings on a Vision?

Started by Glyn

Replies: 1
Views: 1,380

April 15, 2007, 04:59:01 PM
by louthepou

What's the threading on the screw holding the tank on?

Started by vavision

Replies: 2
Views: 1,381

October 28, 2005, 07:45:15 PM
by Lucky

Only starts once

Started by russellsea

Replies: 3
Views: 1,382

July 16, 2009, 04:00:51 PM
by Coil Coyle

Stuck Pivot Shaft Bolt

Started by visionben

Replies: 2
Views: 1,382

September 22, 2006, 02:25:39 PM
by ps2/bikevision

float level

Started by thisandthat

Replies: 1
Views: 1,383

September 02, 2009, 09:48:39 PM
by funkamongus

Understanding the Theory behind the flapper

Started by Extent

Replies: 2
Views: 1,384

May 26, 2009, 08:51:42 PM
by QBS

leaky front end

Started by wilson

Replies: 4
Views: 1,384

March 11, 2009, 08:06:33 PM
by wilson

Overloaded (melted plastic connector block) rectifier conector?

Started by MikeScoot

Replies: 2
Views: 1,384

November 25, 2019, 04:44:53 AM
by MikeScoot

i really need help

Started by Chivo1944

Replies: 4
Views: 1,386

May 02, 2008, 01:45:27 AM
by Rick G

rekeying the Vision locks

Started by Lucky

Replies: 2
Views: 1,386

March 05, 2008, 07:06:14 PM
by Cdnlouie

Rev limiter or TCI?

Started by SonnyT

Replies: 3
Views: 1,389

September 28, 2020, 09:44:40 PM
by SonnyT

Revs take a while to go down, won't start when hot/warm

Started by jono1798

Replies: 2
Views: 1,389

June 02, 2010, 08:47:01 AM
by Lucky

Rear footpeg idea - from Ninja 250

Started by Mike Jacobs

Replies: 1
Views: 1,389

September 21, 2010, 09:52:53 PM
by Rikugun

Triple tree swap?

Started by Jimustanguitar

Replies: 3
Views: 1,389

June 28, 2009, 12:05:10 PM
by YellowJacket!

holes in bottom of airbox

Started by kwells

Replies: 2
Views: 1,389

June 13, 2006, 11:21:38 PM
by kwells

Metric thread pitches and more...

Started by Tiger

Replies: 2
Views: 1,393

June 27, 2011, 08:43:43 PM
by motoracer8

Front Fairing Removal

Started by WGuaire

Replies: 1
Views: 1,394

October 13, 2019, 04:03:00 PM
by WGuaire

can't get the rear axle out?!?!

Started by reckon

Replies: 1
Views: 1,394

August 10, 2007, 09:06:21 PM
by reckon

Dragbar

Started by Staffan

Replies: 1
Views: 1,395

April 21, 2008, 10:57:35 PM
by Rick G

Oil pressure switch scren thread size?

Started by raub

Replies: 2
Views: 1,397

March 27, 2011, 12:40:11 PM
by raub

Carburetor Modification Question

Started by Re-Vision

Replies: 1
Views: 1,397

September 17, 2009, 05:17:28 PM
by Lucky

crud forming under throttle plate

Started by Extent

Replies: 2
Views: 1,398

September 15, 2009, 01:36:46 AM
by inanecathode

82 oil cap o-ring size?

Started by Lucky

Replies: 1
Views: 1,398

August 20, 2010, 04:38:20 PM
by Lucky

Electrical Switches

Started by Re-Vision

Replies: 2
Views: 1,399

November 03, 2009, 02:01:24 AM
by Rick G

Wiring Harness Repair.

Started by lexx790

Replies: 3
Views: 1,400

August 10, 2009, 05:24:35 PM
by lexx790

Basic Specs

Started by Minitor911

Replies: 2
Views: 1,400

April 10, 2007, 11:01:51 PM
by Minitor911

Master cylinder rebuild

Started by motor29

Replies: 1
Views: 1,401

October 29, 2011, 03:22:40 PM
by Re-Vision

Carb Cleaning

Started by PeteXS/GS/CB/XZ

Replies: 3
Views: 1,402

February 01, 2011, 07:02:39 PM
by PeteXS/GS/CB/XZ

Vision Artwork

Started by Re-Vision

Replies: 2
Views: 1,403

April 07, 2011, 10:48:48 PM
by Re-Vision

HELP! - Tach is stuck

Started by sunburnedaz

Replies: 2
Views: 1,404

October 07, 2009, 10:26:44 PM
by sunburnedaz