News:

We would like to thank our supporting members for their generosity.

Main Menu

1982 Vision and Venture rear end

Started by charlie h., May 04, 2012, 06:38:44 AM

Previous topic - Next topic

charlie h.

Hi everyone,
   I am new to the forum but not to Visions, having purchased one new in 1982. Afrer 17k it lunched the cam when the timing gear bolt came loose...  :(
   I now have a low mile(6600) 82 Vision with the sport fairing, and also have several 1st gen Venture Royals which I love! My question is, will a Venture rear end fit the Vision, and would it raise the ratio for touring/ top end? I have a spare pig that I can use, and cursory inspection shows similar mounting. Anyone have any knowledge? I have a Tt600 shock that i will install shortly also! Thanks in advance for replies.

Lucky

We don't know of any conversion like that that will just bolt on, so you would be the first. Will it work? maybe. I guess it's fairly obvouis that you'll have to look everything over & see if everything lines up, including drive shaft. take lots of pictures for us..

There is a way to increase gearing for lower rpms at crusing speed: install an Euro clutch basket & driven gear. that works too...

Good luck, keep us posted.

--Lucky
1982/3 XZ550 Touring Vison, Gold on Black

jefferson

It is my understanding that all the diffs of that era were the same ratio wise. In order to change the gear ratio the ring gear would have to change diameter and there isn't room for it to get larger. A taller ratio might be possible as the ring gear would get smaller, but there might not be room for the pinion to get bigger. I think they will be the same. Manuals for both bikes might help. The one for the Vision lists the ratio as 3.07 but I think it is including the gears at the front.  It shows 19/18 times 32/11.

Jeff

The Prophet of Doom

Doesn't the Venture have a 16" Rear wheel ?  That would change things a bit


Rick G

It also had a bigger tyre . The diameter is close to the same.
Rick G
Go soothingly on the grease mud, as there in lurks the skid demon
'82.5 Yamaha XZ550 RJ  Vision,
'90 Suzuki VX800, 1990 Suzuki DR350.
'74  XL350   Honda , 77 XL350 Honda, 78 XL350 Honda, '82 XT 200 Yamaha, '67 Yamaha YG1TK, 80cc trail bike

charlie h.

Well, you are all correct kinda, the vmax had a lower ratio rear gear which you could swap into the venture for more acceleration. I also looked at the Vision splines on the rear wheel and they look very similar to the spare rear wheel i have for the venture, so i would use the Vision wheel. The pigs are a little different, but the ratios may be different, as the venture redlines at 7,500rpm aand the vision at 10krpm. Now if the ring and pinion are interchangeable, it may be the taller ratio might fit into the vision pig.... then, the 750 virago has a pig that looks identical (81-83) to the vision and they are both monoshock swingarms with shaft drive.Same thing, lower redline on the 750. Might be a way to get taller gears for the vision with minimal muss and fuss. What do you think?

jefferson

I am going to go out on a limb and say that the gearing difference between the Vmax and Venture is somewhere other than the rearend. I am betting that the gears at the front of the driveshaft are different, or it could be the primary gears which I think would be most likely. Venture primary would be like our euro gears and the Vmax would be what we have stock.

Rick G

This discussion was brought up years ago. All the ring and pinions are the same. Gearing differences are in the primary drive. I was told (but did not verify) that the "euro gears" are the same as the SR 500. The reason for this is that the primary drive gears are cheaper to produce than the ring and pinion.
Rick G
Go soothingly on the grease mud, as there in lurks the skid demon
'82.5 Yamaha XZ550 RJ  Vision,
'90 Suzuki VX800, 1990 Suzuki DR350.
'74  XL350   Honda , 77 XL350 Honda, 78 XL350 Honda, '82 XT 200 Yamaha, '67 Yamaha YG1TK, 80cc trail bike

The Prophet of Doom

XZv2 put a XV70 wheel on his bike "The 16" wheel has the same brake and it fits right into the XZ rear fork."

Check it out on http://xz550.nl/ under "The Sidecar"

Rikugun

I think he used  a Virago 750 wheel. I believe the wheel height was lower ie the circumference was less. He did that to mimic a numerically higher overall ratio to ease taking off from a stop with the additional weight of the side car. He did not mind losing top end as the rig was unstable at higher speeds anyway.  :(  I think the OP is looking for taller (numerically lower) overall ratio. I think it also lowered the back to match the front that he lowered.

Interestingly he also reversed the forks left to right to end up with a leading axle fork in the interest of adding stability to the handling characteristics. :) I'm considering trying this to see how it affects handling without the sidecar of course.  ;)
It is far better to grasp the universe as it really is then to persist in delusion, however satisfying or reassuring.  Carl Sagan

Rick G

I was going to try it when I bought my first XV. It puts the brake caliper on the front of the right fork leg , which is less desirable .
Rick G
Go soothingly on the grease mud, as there in lurks the skid demon
'82.5 Yamaha XZ550 RJ  Vision,
'90 Suzuki VX800, 1990 Suzuki DR350.
'74  XL350   Honda , 77 XL350 Honda, 78 XL350 Honda, '82 XT 200 Yamaha, '67 Yamaha YG1TK, 80cc trail bike

Rikugun

Yup, I've considered the various functional and aesthetic repercussions and am OK with them depending on the positives.  :) Plus, it's reversible.  ;)
It is far better to grasp the universe as it really is then to persist in delusion, however satisfying or reassuring.  Carl Sagan

Walt_M.

It would be reversible provided you survive the test ride. Reversing the forks will reduce the trail over an inch! Not a good thing for an already quick handling bike.
Whale oil beef hooked!

Rikugun

Walt you curmudgeonly old fart I knew you cared!   :-*  :-*

I agree on paper it looks wrong. What's confusing to me is another bike of mine with the same castor angle  and 3/4" less trail has a completely different feel to it.  I'd describe it as rock solid vs. the V's rather twitchy, wobble prone nature.  :o  :(
It is far better to grasp the universe as it really is then to persist in delusion, however satisfying or reassuring.  Carl Sagan

treedragon

I know someone who tried forks around the other way.

After the first, and only, ride he came back looking very pale and avowed that the standard setup worked really well all things considered...................  ;D  ;D

 
There is always a way

Rikugun

Thanks for the report Treedragon.  :)

Oh, and my apologies to charlie h for taking this off topic!  :-[  :)
It is far better to grasp the universe as it really is then to persist in delusion, however satisfying or reassuring.  Carl Sagan

Rick G

I do not find the  VX "twitchey", nor does it have a " wobbly prone nature". Perhaps yours need repair???
It handles marvelously quickly in any situation . At speeds over 80 mph , in a large radius sweeper it runs out of horsepower, to drive out of the curve , but is not the least unsettling.
Rick G
Go soothingly on the grease mud, as there in lurks the skid demon
'82.5 Yamaha XZ550 RJ  Vision,
'90 Suzuki VX800, 1990 Suzuki DR350.
'74  XL350   Honda , 77 XL350 Honda, 78 XL350 Honda, '82 XT 200 Yamaha, '67 Yamaha YG1TK, 80cc trail bike

Rikugun

It's all a matter of perspective and degrees Rick. As with any topic there will be those with various positions. I've been fortunate and had the opportunity to ride many bikes of various types and as I'm sure you are aware some are inherently more stable than others. On the other hand, some folks have much less exposure so their perspective is limited and others will never push the bike to experience it's limits.

In another thread someone posts his concern about a high speed wobble. At the time my position in that thread was challenged, 60% of the respondents site having experienced some degree of headshake or wobble. That is significant. Thirty percent don't say one way or the other but if you read between the lines I suspect a number of them have experienced some unsettling event at some point or another. Only one respondent claims the platform to be rock solid.  These are simply not the stats of a rock solid handling bike.

No bike is perfect. When the V is pushed it can reveal handling deficiencies. Stack up a few problems and you've got a potentially dangerous situation when the bike is pushed hard.  :o Why do you suppose aftermarket shocks and fork braces are so coveted and Progressive fork springs a requirement?  In a magazine test from late '82, four half litre bikes are compared in various modes from running errands to track time. Only the Vision received comments concerning handling woes that could not be addressed with adjustments provided in stock trim. Perhaps the opinion of professional cycle testers carries more weight than my assessments.   :)

For those that would question my loyalty to the bike let me assure you I would not invest the time and money if I didn't love this bike! It has many great qualities. When you're smitten you can even accept minor faults as "charming quirks"  :D Marvelously quick handling does not necessarily a stable bike make. Smitten, absolutely. Blinded by love, not by a long shot!  ;D 
It is far better to grasp the universe as it really is then to persist in delusion, however satisfying or reassuring.  Carl Sagan

Rick G

I can agree with a great deal of what you said . I was an active wrench from 1963 to 1980 and continued as an owner/mechanic . Went back to it when I first retired in OR. in a greasy hole. (lots of old wobbly bikes there! I've owned way over a hundred and 25, bikes (lost count)  and as a wrench have ridden thousands of bikes on test rides. Many bikes resent being pushed hard on a twisty road.I don't  find the XZ one of those, it seems to enjoy it. I've pulled stuff that I wouldn't try on anything less that a modern sport bike , but my XZ handles it fine.
OK its not stock , there are spacers on the fork springs (didn't like the Progressives ) Tapered rollers on the T stem, and an '83 shock. and the bars are different. But those add a small measure of comfort . I have the four bike comparison article and can say I didn't agree with all of it , I've ridden all of the bikes tested at one time or another. It may be, that I do NOT like four cylinder bikes. I may be biased against them as I had to work on them, but to me there power band is to far up the rpm scale , not enough low rpm torque.
Rick G
Go soothingly on the grease mud, as there in lurks the skid demon
'82.5 Yamaha XZ550 RJ  Vision,
'90 Suzuki VX800, 1990 Suzuki DR350.
'74  XL350   Honda , 77 XL350 Honda, 78 XL350 Honda, '82 XT 200 Yamaha, '67 Yamaha YG1TK, 80cc trail bike

fret not

1981 GS 1100.  The cheap one with wire spoke wheels.  Bags of low RPM torque.

Regarding whether the venture and XZ read drives can swap, I doubt it but really don't know.  The Venture is about twice the size of the Vision, so logic tells me probably not.
Retired, on the downhill slide. . . . . . . . still feels like going uphill!