TechTalk (Moderator: admin)

Need a Measurement of Distance Between Triple Clamps

Started by kevin g

Replies: 2
Views: 1,226

April 30, 2020, 10:32:59 PM
by kevin g

Rev limiter lead - which one is it

Started by MikeScoot

Replies: 2
Views: 1,305

April 18, 2020, 03:56:09 PM
by MikeScoot

any suggestions to cause of this issue?

Started by carlharri123

Replies: 16
Views: 2,687

April 09, 2020, 10:42:46 PM
by kevin g

Modifications to standard mufflers

Started by MikeScoot

Replies: 15
Views: 3,335

March 31, 2020, 09:54:43 AM
by cafevision

Putting the Spin On your Vision

Started by injuhneer

Replies: 13
Views: 2,856

March 22, 2020, 09:44:52 AM
by jefferson

New stator & r/r wiring question

Started by DBVision510

Replies: 11
Views: 2,550

March 06, 2020, 07:40:57 PM
by DBVision510

Trip meter knob

Started by MikeScoot

Replies: 6
Views: 2,136

February 21, 2020, 03:40:51 AM
by MikeScoot

130/80 rear tire

Started by MikeScoot

Replies: 12
Views: 2,395

February 20, 2020, 10:49:59 PM
by fret not

Carb boots/joints

Started by RBFD415

Pages1 2

Replies: 28
Views: 8,580

February 18, 2020, 10:42:36 AM
by injuhneer

Fork dismantling question

Started by pinholenz

Replies: 11
Views: 4,755

February 15, 2020, 05:08:55 PM
by MikeScoot

1983 getting 11.96 volts

Started by WGuaire

Pages1 2 3

Replies: 42
Views: 7,851

February 13, 2020, 09:08:09 AM
by WGuaire

Shindengen SH775 Regulator/Rectifier install and relocation

Started by vl5150

Pages1 2

Replies: 21
Views: 9,659

February 13, 2020, 08:50:17 AM
by injuhneer

Old motor

Started by MikeScoot

Replies: 19
Views: 3,195

February 02, 2020, 03:00:42 AM
by MikeScoot

Footpeg rubbers

Started by MikeScoot

Replies: 4
Views: 1,509

January 30, 2020, 08:40:51 AM
by WGuaire

Very low compression in rear pot

Started by MikeScoot

Replies: 7
Views: 1,628

January 19, 2020, 01:52:30 AM
by MikeScoot

Oil Change 2.6L

Started by WGuaire

Replies: 5
Views: 1,918

January 15, 2020, 08:59:58 AM
by WGuaire

Starter oil seal

Started by MikeScoot

Replies: 9
Views: 1,873

January 14, 2020, 06:41:04 AM
by MikeScoot

Painting your Vision

Started by MikeScoot

Replies: 9
Views: 2,177

January 13, 2020, 04:07:29 AM
by MikeScoot

Use front type exhaust gaskets on rear?

Started by MikeScoot

Replies: 4
Views: 1,747

January 06, 2020, 02:23:58 PM
by MikeScoot

TCI repair

Started by auto

Replies: 14
Views: 3,371

December 27, 2019, 03:28:09 AM
by MikeScoot

Exhaust gaskets

Started by MikeScoot

Replies: 6
Views: 3,121

December 13, 2019, 09:22:10 PM
by MikeScoot

How to reach rear exhaust screws to head with engine in frame?

Started by MikeScoot

Replies: 6
Views: 4,011

December 12, 2019, 05:40:28 AM
by MikeScoot

caliper rebuild kits with slider pin boots - or calipers

Started by MikeScoot

Replies: 8
Views: 6,630

December 11, 2019, 04:43:54 AM
by MikeScoot

Rear wheel not centred in swing-arm.

Started by MikeScoot

Replies: 10
Views: 4,145

December 06, 2019, 11:58:30 AM
by injuhneer

Mosfet regulator/rectifiers

Started by MikeScoot

Replies: 10
Views: 4,326

December 04, 2019, 05:41:46 AM
by MikeScoot

Separate final drive from swing arm

Started by MikeScoot

Replies: 5
Views: 3,805

December 04, 2019, 04:19:08 AM
by MikeScoot

1983 Petcock Rebuild

Started by kevin g

Replies: 5
Views: 2,101

December 02, 2019, 10:54:29 PM
by injuhneer

YICS ports appear to be connected to each other.

Started by MikeScoot

Replies: 16
Views: 3,552

November 27, 2019, 05:52:51 AM
by MikeScoot

Overloaded (melted plastic connector block) rectifier conector?

Started by MikeScoot

Replies: 2
Views: 1,401

November 25, 2019, 04:44:53 AM
by MikeScoot

paint colours

Started by davecut

Replies: 13
Views: 5,074

November 24, 2019, 02:39:17 PM
by injuhneer

Petcock alternative for 1982

Started by vl5150

Replies: 1
Views: 2,114

November 22, 2019, 08:41:58 AM
by injuhneer

Need length of sport mirror mounting bolt

Started by VisionSeattle

Replies: 2
Views: 1,611

November 20, 2019, 11:58:37 PM
by VisionSeattle

Do I need new stem bearings?

Started by MrGonzo

Replies: 4
Views: 1,870

November 12, 2019, 11:35:06 PM
by injuhneer

Emulsion Tube Removal

Started by cvincer

Pages1 2

Replies: 24
Views: 9,684

November 11, 2019, 10:26:57 AM
by injuhneer

Bad stator

Started by skucera

Replies: 12
Views: 4,616

November 10, 2019, 08:48:04 PM
by injuhneer